Reconstruction and operation of crisol furnace for casting aluminum scrap in Ayacucho
DOI:
https://doi.org/10.15381/iigeo.v27i53.27729Keywords:
Aluminum, scrap, foundry, crucible furnace, recycleAbstract
The general objective was to rebuild and put into operation the crucible furnace for smelting aluminum scrap at the National University of San Cristóbal de Huamanga – Ayacucho. The specific objectives were to evaluate the stages of the reconstruction regarding the modification of the design and operation of the crucible furnace for the smelting of aluminum scrap. Obtaining objects (finished products) through different molding techniques. Carry out material and energy balances using oil and gas as fuel. The level of research was technological experimental, and the analytical method was comparative. The design was explanatory experimental. 4 tests were carried out using oil as liquid fuel, then gas, thereby improving the aluminum smelting process, with a high recovery percentage. It was implemented with an automated control panel for the use of gas as fuel. Different molding techniques were also experimented with. The material balance, calculations of the kiln load and products, calculation of the fed air and gases leaving the kiln were carried out. It is recommended to continue with other research in the field of transformative metallurgy since one way to reduce aluminum pollution is by recycling it, which is why it is considered a sustainable metal.
References
Alvayero, J., & Huezo, C. (2009). Diseño de un horno de fundición de alumnio. [Tesis de grado]. Universidad Centro Americana "José Simeón Cañas", El Salvador.
Antay, M., & Pfuro, B. (2022). Diseño y construcción de un horno de crisol basculante para la fusión de aluminio para el laboratorio de fundición y moldeo de la Escuela Profesional de Ingeniería Metalúrgica. [Tesis de grado] Universidad Nacional de San Antonio Abad del Cusco, Perú. https://repositorio.unsaac.edu.pe/handle/20.500.12918/6783
Aquima, W., & Carlos, D. (2022). Diseño y construcción de un horno de crisol basculante a gas natural para fusión de aluminio. [Tesis de grado]. Universidad Nacional de San Antonio Abad del Cusco, Perú. https://repositorio.unsaac.edu.pe/handle/20.500.12918/6508
Basilio, H., & Basilio, C. (2022). Sistema de reducción para colada en fundición de pequeñas cantidades de metales preciosos. Revista Del Instituto De investigación De La Facultad De Minas, Metalurgia Y Ciencias geográficas, 25(49), 253-257. https://doi.org/10.15381/iigeo.v25i49.23010
Del Valle, C. (2021). Factores predominantes que afectan el medio ambiente por el uso de la resina furanica en moldes para la fundicion de metales. Revista Del Instituto De investigación De La Facultad De Minas, Metalurgia Y Ciencias geográficas, 24(48), 197-204. https://doi.org/10.15381/iigeo.v24i48.21772
Dionicio, E., Vega, V., Tabuchi, E., Gonzáles, O., Rosario, S., Villacorta, L., & Dionicio, N. (2004). Influencia del molde y el tratamiento térmico en las propiedades del bronce-aluminio. Revista Del Instituto De investigación De La Facultad De Minas, Metalurgia Y Ciencias geográficas, 7(14), 23-32.
Fernández, A. (2019). Instalación de una fábrica de perfiles en la Ciudad Puno, usando como materia prima aluminio reciclado. [Tesis de grado]. Universidad Nacional del Altiplano, Perú. http://repositorio.unap.edu.pe/handle/20.500.14082/10480
Flores, E., & Orellana, R. (2014). Diseño y construcción de un horno de crisol para aleaciones no ferrosas. [Tesis de grado] Universidad de El Salvador, El Salvador.
Gabriel, J. (2023). Economía circular y el valor agregado de los minerales. Lima: IX Congreso Internacional de Sostenibilidad Socioambiental en Metalurgia y Minería.
Kida, J., Yupanqui, D., Sihua, C., Cabrera, J., & Farfán, J. (2010). Horno de crisol MCJ para fusión de metales no ferrosos a GLP. Cusco: Universidad Nacional de San Antonio Abad.
Mestanza, D., & Lara, V. (2012). Diseño y construcción de un horno de combustión industrial para fundir aluminio. [Tesis de grado]. Escuela Superior Politécnica de Chimborazo, Ecuador. http://dspace.espoch.edu.ec/handle/123456789/1974
Niño, N. (2012). Diseño y fabricación de un horno de fusión basculante para aleaciones no ferrosas, empresa J's Servipetrol LTDA. Bucaramanga: Universidad Industrial de Santander.
Perez, F., & Soto, A. (2009). Diseño, cálculo y construcción de un horno de fundición de aluminio tipo basculante y sus moldes. Pamplona: Universidad de Pamplona.
Quispe, R. (2020). Diseño y construcción de moldes permanentes en bronce para fabricación de cabezas de león ornamentales de aluminio, en la empresa Fabrimetx, Espinar - Cusco. [Tesis de pegrado]. Universidad Nacional del Altiplano, Perú. http://repositorio.unap.edu.pe/handle/20.500.14082/14524
Villacorta, H., Falconi, V., Rengifo, W., & Martínez, M. (2011). Influencia del cobre en la transformación Gamma-Alfa en la fundición gris y nodular-templabilidad. Revista Del Instituto De investigación De La Facultad De Minas, Metalurgia Y Ciencias geográficas, 14(28).
Zuñiga, A. (2023). Economía circular y el valor agregado de los minerales. Lima: IX Congreso Internacional de Sostenibilidad Socioambiental en Metalurgia y Minería.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Alberto Cossio Herrera, Abraham Fernando Trejo Espinoza, Angel Gustavo Davalos Calderon, Jorge Alberto Ortiz Barreto
![Creative Commons License](http://i.creativecommons.org/l/by/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution 4.0 International License.
AUTHORS RETAIN THEIR RIGHTS:
a. Authors retain their trade mark rights and patent, and also on any process or procedure described in the article.
b. Authors retain their right to share, copy, distribute, perform and publicly communicate their article (eg, to place their article in an institutional repository or publish it in a book), with an acknowledgment of its initial publication in the Rev. Inst. investig. Fac. minas metal cienc. geogr.
c. Authors retain theirs right to make a subsequent publication of their work, to use the article or any part thereof (eg a compilation of his papers, lecture notes, thesis, or a book), always indicating the source of publication (the originator of the work, journal, volume, number and date).